Rotec AI

Tools

Bearing SelectorPick the right bearing, step by stepVerify a BearingLife, safety factor and fitsLoad CalculatorLoads from your machineWorked templatesFan, gear and shaft load templatesCross-ReferenceNewSame size from other makers. Free, no sign-upBearing AutopsyNewUpload a photo, get the likely causesFailure AnalysisRead damage, find the causeCondition MonitoringVibration, envelope, oil clues, RCMLubricationGreases, oils, cleanliness, oil lifePM criticalityScore assets, set the PM orderEquipment AnatomyMotors, pumps, fans, gearboxesFAQ and quick checksSearch the basics in plain languageFind a DistributorSuppliers by brand and city

Learn

Free calculatorsLife, grease, oil, loads and moreFind a bearingSize, rating and equivalents by designationFailure modesDamage types, causes and fixesBearing materialsSteels, heat treatment, ceramicsCondition monitoringVibration, envelope, oil clues, RCMKnowledge libraryLubrication and reliability articlesBearings by machineMotors, pumps, mills, kilns and moreHow-to guidesBearing life, grease, failures, numbersShaft alignmentSoft foot, procedure, tolerances, heatField casesFailure investigations and monitoring cases (licence)Lubrication guidesGreases, oil systems, oil life and costPM criticality matrixRank assets by what a failure costsQuick answersPlain-language answers to common questions

Play

PlaygroundLearn engineering by playing with it

More

PricingPartnershipsExpertsContact
Stribeck curve game logo
Lubrication · free · play it

The Stribeck curve game: keep the bearing in its sweet spot

Quick answer

The Stribeck curve shows how friction changes with oil viscosity, speed and load. Too little oil film and metal touches metal. Too much and the oil itself drags and heats. Move the sliders, watch the dot, and find the zone where a bearing lives longest.

Teaching model. It shows the shape of the curve and the three regimes, not the friction of a particular bearing.

Goal:

Viscosity ratio κ–
Oil at running temp–
Needed–

How to read the curve

Zoneκ (viscosity ratio)What is happeningWhat it means for the bearing
Boundarybelow about 0.4The oil film is thinner than the surface roughness, so metal touches metal.High friction and wear. Common at start-up, at very low speed and with thin or hot oil.
Mixedabout 0.4 to 1The film carries part of the load and the peaks still touch.Some wear and heat. Life is shorter than the catalogue figure.
Full filmabout 1 to 4The oil film fully separates the surfaces.Low friction, low wear. This is the zone to aim for.
Too thickabove about 4The surfaces are separated, but the oil is churned and sheared.Friction and temperature climb again, and energy is wasted.

How the game calculates

κ is the oil's actual viscosity at running temperature divided by the viscosity the bearing needs for its size and speed. The needed viscosity uses the standard bearing-life relation: for speeds under 1000 rpm, 45000 × rpm−0.83 × dm−0.5, and above 1000 rpm, 4500 × rpm−0.5 × dm−0.5, in mm²/s. The oil's viscosity at temperature uses the standard viscosity-temperature relation for a mineral oil with a viscosity index of about 95. The load setting is a teaching simplification: heavier loads need a thicker film, so it raises the needed viscosity.

Real selection also depends on contamination, additives, the lubricant type and the operating conditions. Confirm any real selection with your lubricant or bearing supplier.

Questions

What is the Stribeck curve?

A graph of friction against a combination of viscosity, speed and load. It shows three regimes: boundary, mixed and full-film lubrication. Friction is highest in boundary, falls through mixed, is lowest in full film, and rises slowly again if the film is too thick.

Why does every start-up pass through boundary lubrication?

The oil film builds up with speed. At standstill there is no film, so the surfaces touch. As the shaft speeds up, the film forms and the bearing moves into full film. Try the Start-up run button to watch it happen.

What does the viscosity ratio κ tell me?

It compares the oil you have with the oil the bearing needs. A value of 1 means just enough. Higher values mean a thicker, more protective film, until the oil becomes too thick and adds drag.

Is this a design calculator?

No. It is a teaching model. For a real application use the Lubrication tab and confirm with your lubricant or bearing supplier.

Related: Oil systems and viscosity selection · Oil life and cost · Grease finder · Troubleshoot grease problems · Failure analysis